Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Hello
I’m trying out the new nRF52832 (QFAA-AA0) with preview kit pca10036. I have S132 softdevice installed and running the beacon example from SDK 0.9.0 which appears...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
Now I want to store some data above bootloader( the address after bootloader), but every time when I call the function pstorage_init(), the function will defaultly set my...
How to add single 128-bit characteristic uuid. It's not based on service uuid.I have tryed the link text ，It's work,but it's something wrong .
I am working on ios ble midi...
I developed a custom board with nRF51822_xxAA on it, working on low voltage mode.
I can program some basic things on it using Keil uVision 5.15 and a J-link to flash the...
Hi,
I'm trying to use the pstorage on a central device.
An event of BLE_GAP_EVT_ADV_REPORT is called by discovering some ble devices while a central device is scanning...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. My application uses the watchdog timer. I...
Hi,
I'm developing an Android application that uses Android DFU Library and I want to set the number of packets that are sent every notification interval to 1. I couldn...
On the BMD200 evaluation kit ( www.rigado.com/.../) using the nrf58001:
--> UART TX (pin P0.09) works - confirmed with logic analyzer and Serial Port Terminal on the PC...
We are operating on nRF51822 QFAC with S130 SD. We have a functionality where the device switches between scanning and advertising. Strangely we have observed that after few...
Hi,
When i read the ble_peripheral sample of the SDK, i have a question below.
If my peripheral is connecting a central, then i use function sd_ble_gap_disconnect() to disconnect...
Hi,
The established time tick source for FreeRTOS is RTC1 via the APP_TIMER module. I am trying to shift the basis of the APP_TIMER from RTC1 to TIMER2, so that I can use...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I have an nRF52 dev board (PCA10040). I have been using this board for measuring current. I am using the Keil tools.
Yesterday I made a change to main.c in the ...
Hello,
I am working on S120 v2.1.0 and SDK 9.0 for central and I am able to connect to my iPad. Now I need the central to delete the bonding information stored using pstorage...
