Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
In libuweave project there is an example demonstrating communication between nRF51/52 and android client app. The Android client application is named SimpleLock.apk. But I...
Hi
I am trying to use nrf51822 as both peripheral and central device for my application.
nrf51822 as peripheral checked satisfactorily with a smart phone as central device...
Hello,
I use EV-board PCA10040 and run I2C demo on path nRF5_SDK_11.0.0_89a8197\examples\peripheral\twi_sensor\pca10040. I measured the current over 5.7mA .if modifing the...
Hi.
I've got little problem with the uart connection to one peripheral. It's a normal 2-line connection without HW flow control. I'm using app_uart_fifo. HW is nRF52 with...
Hello,
i have a problem with the PCA10040. I try to set up a ANT Transmit Channel.
If "ant_channel_init" is called from main everything works fine.
But if it's called...
Hello,
I am developing in NRF52 with SDK v11. Initially I want to use CMSIS DSP library for statistic and FFT functions. However, I read that CMSIS Pack is not supported...
Hi,
I wrote a functional firmware which has been tested and valited on a nrf51822 QFAA, but unfortunately I need more RAM to fit the requirements of my application so I...
In the Android version of the Master Control Panel I'm sure that earlier versions of it hid the 'Connect' button for non-connectable devices. It seems they all have it now...
I'm starting to get things moved over to Peer Manager in SDK11 and when I call pm_conn_secure I get NRF_ERROR_NO_MEM. When reading the manual it states that this error means...
I'm using sdk10, I tried the bonding feature using device_manager and it's working. but then when I perform DFU, the bonding information is erased. I can't modify the bootlader...
There's a note in the migration guide which says .. very ominously ...
Applications must not modify the SEVONPEND flag in the SCR register when running in priority level...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear Sir
In nRF51822 xxAA (Ram is 16kB),
softdevice(s120) is using RAM (address: 0x2000_0000 ~ RAM_R1_BASE).
I think that SoftdDevice region is used, after sd_softdevice_enable...
Hello,
It just a diode drop away from 3.9 to 4.2, and 20% typical of a Lipo discharge, just wondering whether the IC design and process is really that tight. The nRF52...
