Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I have developed two different application on nRF51822 with two different location. One is start from 0x1D000 with max size of 16 KB and another start from 0x21000...
When i am trying to transfer data over air using sd_ble_gatts_hvx() function every time i am getting err_code 12 ( NRF_ERROR_DATA_SIZE ) error.
Here i can send data from...
I'm working with ble_app_uart_s130.
Compilation is fine and it works as expected in hardware.
I'm going to add application timer and scheduler.
To do that I have to set...
I want to use ADC / PWM / I2S / UART / SPI / I2C / at a time.
So, Can I use all GPIO pin assign any function?
If I can't use some function at a time, I want to know the...
Launch an example for UART (BLE PERIPHERAL) on the board PCA10040. When try to set the parameter APP_ADV_TIMEOUT_IN_SECONDS = 0 (no timeout) get returned NRF_ERROR_INVALID_PARAM...
Hello,
I have a question regarding AVDD pin.
I am using nRF51822 CEAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between VDD and GND...
Hi everyone
I'm facing a weird problem in my design and FreeRTOS. Apparently, my system was working fine, but along I'm adding more tasks, i've detected the system stops...
I'm using RS485 driver on NRF51822 uart. I started software developing with ble_uart exapmle.
RS485 as always has direction control inputs.
Before data transfer to uart...
In my app I have the following:
s110
20 ms min connection interval
100 ms max connection interval
4000 ms con_sup_timeout
I'd like to set the slave_latency...
Hi,
The documentation states -96dBm rx sensitivity for 1mbit BLE mode and -93dBm for proprietary 1mbit mode.
Is it possible to use BLE mode (3 in MODE register) but...
I want to scan for peripheral devices in central-role and at the same time i want to broadcast in peripheral-role. How do i have to initialize the Softdevice in this case...
Hi,
I'm originally iOS app developer.
I have been developing with custom PCB that based on nRF51 chip. (not nordic development kit)
My PCB has a gyro sensor and some...
Hi,
Whenever i m trying to upgrade my application using iphone with binary file then i get "unsupported DFU" error. what is meaning of this error and how can i resolve...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
