Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I used two 51822 modules for my project. One should send a byte and other one should receive.
I used the exact same configurations of radio examples (transmitter and...
I am trying to read an analog value on the GPIO port into my application. Looking through the examples, there aren't any that help solve this problem as the ADC example is...
I have tried to follow the installation instructions and have installed nRFGoStudio, the Keil MDK-ARM, and downloaded the latest nRF52 SDK. I also installed all of the device...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
If we want to obtain sets of five "Bluetooth stylish temperature sensors, do you have a selling point in The Netherlands? If not maybe a way to obtain this by mail or parcel...
Hi!
I am coding soft for nRF52xx. Having looked through the examples I've got one question.
In the preprocessor defined:
NRF52_PAN_24
NRF52_PAN_25
NRF52_PAN_26
NRF52_PAN_27...
We have a nrf51822 chip connected to an arduino-like device. We need to use UART for communication, but without firmware modification the master chip doesn't support USART...
