I'm building a project where I need to sniff bluetooth data exchanged between a Voltcraft SEM6000BT plug and my phone app. The idea here is to capture the BTATT (where the...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hello Nordic team, We are trying to use ST7305 display (custom driver that we have developed using st7789V as refrence ) and acconeer A121 senors on same SPI bus. The A121...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I am using the NRF54L15 DK for development. I have configured the i2c with P1.12 as SCL and P1.14 as SDA.
below is my code in .overlay file
Below is the code...
I have 2 moduls from ebay (rfinchina). I write little librarie for nRF24L01 and my msp430.
When i start my coard and init spi and try read few register - i have problem....
Hi,I use 51822 to make a fitness device. one of the function is advertising current value(Steps,Heart rate,Distance,Calorie) to the phone over BLE. What the default service...
I downloaded nRF51 SDK 5.2.0 and I am studying the examples for S120.
I notices that there's no gcc directory, thus only Keil compiler can be used. Is there a way to use...
Hello,
I have some questions regarding bluetooth low energy and the NRF51 series.
[list=1]1) I have to synchronise maximum 17 sensors, so i will maximum need 4 masters...
Hi.
I am looking for the internal resistance of the ADC pin of my nrf51822. I have looked at the Product Specifications (as well as the Reference Manual and other documents...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
Hi all,
When I receive data from the phone app, I do it via this service handler (and it works):
err_code = ble_services_init(&my_device_service, ble_receive_handler...
error:-559038737 ...line:1128 file_name:src\ll_lm.s0.c
And I can't find this file, so can somebody help?
Why this happen? How can I do to avoid this？ It will cause reboot...
