Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
when I use nRF Connect (or MCP before) to browse my BLE service, I get shown some garbage if I use many characteristics in my service.
When I use 45 characteristics...
Hello people,
I'd like to use the NRF52832 (QFAAB0) / PCA 10040 / S132 development board as a data logger. For that I soldered a micro-sd card reader and started using...
I set the connection as follows:
#define MIN_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(1000...
I am trying to use the mesh network using the nrf51822. I have to use the app_timer with my application. Mesh library and the app_timer library making conflict with the SWI0...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
I have checked the datasheet between 51422 and 51822,they look the same,but why the NRF51422 can flash BLE and ANT+,but 51822 can't? Is the Radio part different,or the Flash...
I have based my firmware on the Proximity Application example.
Now I need to extend my application to support BLE DFU service.
But as i read Extending your application...
Hi,
I am using the flash memory for a few variables and it works very well. Now I have one flag which is defined by #define statement and if it is enable then the initial...
hi,
i have nrf8122 module . want to flash a hex file in it by using nrf51 development kit. is it possible to flash code in the nrf51822 module. other wise please provide...
Hello everybody,
I'm working in a project & need to listen for notification from installed applications in the mobile phone & update the mobile app with some info about...
I have combined Nordic's serial connectivity code and Nordic's serial DFU example.
Upon initial powerup, the nRF51822 draws an expected amount of current (~600uA). When...
I am using nRF Master Control panel for testing my peripheral changes. It works fine until i upgrade my nexus 5 to android Marshmallow. Now the app cant even find BLE device...
Hi all,
I'm using nRF5_SDK_11.0.0_89a8197, if I build any project from it, it deletes all objects files and compile all source files every time it take some unnecessary...
