When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
When exporting the example project BLE_HeartRate from the online IDE to the GCC (ARM Embedded) toolchain, the makefile fails to compile.
First, the compiler throws "fatal...
Hi:
I am using nRF51 Dongle to develop my platform, and software is base on esb_low_power_prx and esb_low_power_ptx in nRF5_SDK_V11.
For production, I need to program...
When I connect to another beacon using sd_ble_gap_connect() scanning on my device is stopped. I have to wait till connection is established or establishing connection fails...
The Nordic set comes with a Device number of it's own. I want to overwrite that device number, or store a device number in a different location in the EEPROM. Is there any...
What files within the FDS are used by the modules of the Nordic SDK?
For example, I know that the Peer Manager uses the FDS as a storage backend. I need to know what files...
Previously I implemented a DFU bootloader. It works fine on s120 softdevice.
But after I ported it to s110 v7.0 softdevice, it can not work. After investigation, I found...
Hi,
i just followed the steps for migrating to peer_manager - as lines out in the tutorial.
However i will never ever get a callback to pm_evt_handler.
I am trying...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
