Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I have two device , one is Tx-Device the other is Rx-Device.
Tx-Device : Auto continued Send 4 bytes data to Rx-Device by Radio.
Rx-Device : Using Radio Interrupt receive...
First of all I'm a BLE novice, so sorry if I'm asking obvious questions. I've built a home project where a battery powered mcu listens for requests over wifi and drives a...
Hello.
I'm trying to do as follows: ONE button used either to wakeup or to put system to sleep. In general almost everything is working but I cannot find how to configure...
HI,ALL
as i known, the BLE key is a six digit pin.
and in the static void device_manager_init(bool erase_bonds) ,the statement shows below:
register_param.sec_param...
According to this post , and this GitHub source file , in the nRF51 chip's mbed implementation:
The ADC reference voltage is 1/3 power supply
read_u16() seems to...
HI,ALL
in the nRF5_SDK_11.0.0-2.alpha_bc3f6a0 , GATT Server Event IDs.
i do not find the read event.
All i found is the BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST .
Now...
Hi, all
Recently I use nrf51822 CEAA, WLCSP package to develop a project on UV (ultraviolet), the UV sensor must be exposed to the sunlight. When we take the product board...
I'm running the DFU example from the nRF5110.0.0 SDK. dfu_dual_bank_ble_s110_pca10028 on the DK and it works perfectly using Master Control Panel, but it does not work from...
I currently have a dualbank bootloader setup and I'm trying to change it to singlebank. If I burn the singlebank bootloader with the jlink it works fine, but if I use the...
Hello,
I modified ble_nus_c to manage multiple connections.
The first time (first client) i call sd_ble_uuid_vs_add in init, it returns OK. The second time ERR_NO_MEM...
both for APP_UART_FIFO_INIT and APP_UART_INIT i never receive APP_UART_DATA_READY
but at least i get APP_UART_DATA sometimes .
most of the times i get APP_UART_COMMUNICATION_ERROR...
I'm trying to monitor the time a signal is high/low on a GPIO. It seems to work alright with timers and PPI, but I wish there was a way to reset the timer upon capture.
...
Hi,
What is the largest possible value of "MAX_VAL" for application timer given below:
"#define APP_TIMER_PRESCALER 0"
"#define M_DELAY APP_TIMER_TICKS(MAX_VAL, APP_TIMER_PRESCALER...
Since UART-BLE is an emulation of UART on BLE, is there a need for physical wiring of the pins (RXD, TXD)? Assuming I'm not using RTS/CTS as I have disabled flow control,...
