Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
Hi Community,
I'm learning the sysbuild stuffs, try to upgrade my code to sdk v2.9.0.
Exercise 2 - Adding custom image - Nordic Developer Academy
I'm using nRF5340DK...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
Environment info:
Tested on own integrated product, and nRF5340 Audio DK.
Firmware built on Fedora Linux 42,
Using the Rust programming language, using embassy-nrf &...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hello,
I would like to know how to build the aws_iot example without network offloading to the modem. I need to make AWS connections through both the nRF9160’s LTE-M connection...
