VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...
Hi there. I have a very long C code that is running correctly on Code:Blocks, Ubuntu Terminal ( using GCC ), Eclipse and on Dev-C++.
However, when I put in on the board...
Hello,
I've been trying to control MCP23017 IO expander with TWI using nRF52832. When I execute the code it stops at nrf_drv_twi_tx. The address pins A(0:2) are 0.
Any...
I have having following configuration:
I want a fail safe method to update firmware on nrf51822 using attached host controller. I looked at serial wire debug interface...
Hello,
I'm running a serialized application based on the SDK 10 and S130 v1 and I am in the process of porting the peer manager to the application µC.
Due to the fact...
I'm trying to set up a system where the sample rate of data being notified to the client from various sensors can be changed by updating a configuration characteristic in...
