Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Using OBS-421 from Connectblue as Central. Using simple AT command to connect and get data. Can connect successfully with Cypress BLE as well as the TI sensortag and get data...
Hello,
When i have a bootloader installed and i try to debug application, it doesn't start application probably because debugger programmed application without the right...
hello everybody,
I'm working in a project using the automated generic bootloader example, I want to do some edits so as I can have an input interrupt at any time, I mean...
I am having trouble with the service discovery of my application. When I click Discover Services it takes several seconds to discover all of the services. For example between...
Hello!
I have a problem with ble DFU application upgrade. I use the Master Control Panel 3.10.0.14 under Win 7 on virtual machine and nordic ble usb dongle.
On the firmware...
I used AdaFruit Bluetooth LE shield previously that uses nRF8001. I can define new customer service using nRFgo studio (which only supports nRF8001). I am moving towards using...
Hi,
I am using pca10040 board. i need to toggle a led in 5sec once. I tried to change the prescale value. But im not able to get that much time delay.
Can any one help...
SDK Version: nrf51_iot_sdk_0.8.0_f1f6187
In SDK all examples are given for PCA10028. Is it possible to run on PCA10001?
What I have done so far with PCA10001:
1.Programmed...
Hello,
I have modified the Android-nRF-Blinky Application to use it with the Datathroughput Demo on the nRF52 DK.
The android application runs on a Nexus 9 with android...
Hi, i try to understand how to use mode for supply voltage measurement. But i have a problem and i get always 1.225 volt
hal_adc_set_input_channel(HAL_INP_VDD2_3);
hal_adc_set_reference...
Hey all,
Wondering if we could use an external 65.536KHz LF clock, or thereabouts, instead of the 32.768KHz? We need better resolution for the RTC, but don't want to turn...
hello im from mexico, last week i order 10 NRF24LE1 and arrived the next wake,
but before i have many cuestion about.
someone can tell me that the burner can work?
compiler...
I had a mbed firmware running on a ST Nucleo 64 that periodically query a sensor for data. It only use the I2C, a button interrupt and a LED for heartbeat. I ported it to...
