I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi all!
I'm trying to move to SDK 14 with some project.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 23..70 all works good.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE > 72 exception happens...
Hello, I am investigating the possibility of integrating the DTM functionality into our app (which uses the softdevice) to allow us to use a single image for production testing...
Hi,
I am using the SAADC example in SDK 12.2.0 together with SoftDevice (S132, v3) and its working fine without any problems. As a modification, I want to uninitialise...
After calling sd_ble_gap_connect() at an arbitrary time, how does the central actually connects to the peripheral?
Assuming the client probably listens only at certain times...
Hi all,
Is there a way to change the UART pins configuration to bypass the segger jlink debugger on the nRF51/52 devices? I would like NOT to use this debugger chip for...
I am trying to receive a string of 708 characters via BLE. As BLE cap a maximum of 20 bytes per transmission, at the mobile app side I break the data to be send every 20 characters...
Hi All.
I wanna to continue Advertising during peripheral connection due connectable ADV prohibited if Peripheral connection established for nRF52840.
Is it possible to...
I'm trying to print a 20 byte array over uart before sending it on BLE. My array contains:
{0x34, 0x12, 0x00, 0xFF, 0x00, 0xFF, ..., 0x00, 0xFF}
However when I try...
Hi, i am actually working on a smart lock and i want to implement an Automatic Unlock.
This functionnality can be really useful, because the door unlock even if your smartphone...
Does the ACL peripheral protect flash from Read/Write/Erase of CPU and all peripherals? or just CPU? or do some peripherals have a privileged access? (such as the CryptoCell...
Hello,
I'm working on a project that needs sha1 hash functionality and I found this thread about the integration of openssl hmac lib:
devzone.nordicsemi.com/.../
...
Hi,
I have been working with Bluetooth mesh. The test I have been performing repeatedly polls a single node and measures the RSSI (as measured from p_message->meta_data...
Hi,
I purchased Thingy:52 I want to develop ble mesh n/w application on Thingy:52.is it possible that I get any sort of support from you in this context.
I'm trying to run the Thread DFU examples on nRF52840, unfortunately I can't get them to work. On the client, I got the bootloader set up and ready, with the client application...
