Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
i'm testing an application on nRF52, with nRF5_SDK_11.0.0-2.alpha and SoftDevice 132.
I took the ble_uart example and added a custom service with some characteristics...
Hello,
i'm trying a bluetooth connection between nrf UART v2.0 installed on my phone(android 4.4) and nRF 8001 (i'm usign nRF2740 card). My microcontroller is a STM32....
Hi.
I made my own board using nRF51822AC.
I want to connect this board to PCA10028.
There is Debug OUT port(P19).
Net names are EXT_VTG, EXT_GND_DETECT, EXT_SWDIO, EXT_SWDCLK...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I'm testing External interrupt.
Current concumption was just 50uA around(low speed advertising mode).
But It goes 1mA around...
Hello
I'm working on a network of nodes with more than 300 nodes
each node is constructed by (1 arduino nano,humidity sensor, 1 relay and NRF24L01 +)
I'm working with the...
Hello. I'm trying to understand twi_sensor sample code on nRF51. (nRF51_SDK_10.0.0_dc26b5e\examples\peripheral\twi_sensor)
I have a trouble finding where the function twi_handler...
Hey,
i've bought the nrf52832 Preview DK some time ago, are there any big changes to the new DK? So if i buy a new nrf52832 IC i can desolder the old IC and use the new...
If I have some value and this value has become out of desired range I want to change property from indicate to notify.
I only found function sd_ble_gatts_characteristic_add...
I'm developing an application for a device which needs to support both DFU and some method of restricting connections to a single central (ie: bonding). This is a challenge...
Hello!
Is there have any tutorial for how to create GATT service on the MCP(master control panel app) and what coding do we need to add to the project?
Hi, I would like to put a nrf51822 device into system off mode and wake it up with a GPIO transition from high to low.
I would like to measure the press time of the button...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
