I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hi,
I have just bought a nRF51822 Beacon Kit. The sticker on it shows that it is a PCA10006, Rev 1.2.0 2015.17 on it.
But I think that it is PCA20006.
What is the best...
Hi
I am getting some weird response from my nRF51-DK.
Situation 1:
When I try to flash it with the Blinky code (\sdk11\examples\peripheral\blinky\pca10028\s130\arm5_no_packs...
I'm trying to under the ble_app_multirole_lesc project and I'm a bit confused about calling sd_ble_auth_key_reply and sd_ble_lesc_dhkey_reply. If you are using Just Works...
Hi,
I am trying to send a HEX command to a device over UART at 9600bps using nRF52 DK, but it never works. However, it works with Arduino (so the receiving device should...
I have nRF52 Development Kit,after my first time programming the Firmware to my board.I can't erase or program it any more?
The nRF52 Development Kit can be connected with...
Hi,
I have read the following posts and understand how low clock frequency mode can be selected
devzone.nordicsemi.com/.../
I've also read in many posts that 4s calibration...
Dear Sir:
Could I use the external reference AREF1(pin0.06) instead of internal VBG 1.2V for ADC operation ?
I do the following settings to config using external reference...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
Hello,
I'm trying to write value to a specified address with ble_flash_page_write .
I'm using ble_flash_page_write after ble disconnect event. I've tested different...
hi Ole BAUCK, my slave device is STPM33 ENERGY METER using this device we can calculate vrms,irms,real power,reactive power,energy and many more.. that device is not having...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. Now it almost works. But after an app image has been successfully transferred...
hi all,
i am using sdk v8.
i want to transmit the address through uart and read the data using UART.
i am using app_uart_get and app_uart_put api's.
PROBLEM:
if i connect...
