Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
I'd like to know three type of ESD models breakdown voltage lower limit.
・Machine model(MM)
・Human body model(HBM)
・Charged device model(CDM)
If nobody have the...
Hello,
i am working with the nRF52 DK and the SDK11. My intention is to receive arbitrary bytes via UART in non-blocking mode.
I have already read the following entry...
Hi I need use s130 softdevice as a central. So i am getting error with my existing code that works fine with s120 softdevice as central.
nordic_sdk_10/components/softdevice...
Hi, Nordic:
I'm testing the DC/DC function as to reduce the radio current. I have done the DC/DC test using pca10028 DK with the code below (SD v2.0.1, SDK11) :
void...
Hi,
I want to develop an ANT+BLE application using the D52Q module. I found the BLE serialization documentation but it's referred to S130, S132 SoftDevices. Is it compatible...
I have recently started getting the following error during a DFU using MCP.
Capture.PNG
Any idea as to the cause of this? What is the best way to debug this?
I am...
Hi,
I am wondering why PSTORAGE_NUM_OF_PAGES is by default set to 2 in the DFU project.
From what I understand the pstorage_raw.c module is used to update bootloader...
In iOS, it is possible for different apps to send data to the same characteristics in the same device by calling retrieveConnectedPeriphrals… Is there a way to identify the...
Hello,
currently, I am trying to get the SPI (master with EasyDMA) to work. I interfaced it with an LED driver IC , which needs some signaling (via GPIO pins) along with...
Hi,
I'm using the nrf52 board with sdk11.
I want to know that i have 100 beacons and my nrf52 is a cenral.
1)How many beacons can scan by the central at a time?
2...
Hi, I have managed to get my nrf51822 DK kit to read LDR sensor values. However the characteristic values are represented as hex on the master control panel and also on the...
Hi,
I'm i'm sniffing the NRF51822 s110, using the Nordic's BLE sniffer (on s120).
The BLE device is in a connection, and do a connection parameter update to a new interval...
Hi All,
I'm trying to update the application firmware of an nRF52 board with OTA DFU.
I have managed to create a .zip package (under linx, gcc compiler, Nordic SDK11,...
