Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...
Hi,
is there any way to connect at the same time multiple devices with Android/iOS nRF UART app to an nRF52832 with ble_app_uart example?
I was thinking about adding advertising...
HI all,
I am setting these parameter as follow in my ble_app_template sample.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) /**< Minimum acceptable connection...
Hello everyone
I'm the proud owner of a nRF52 Prev. DK and trying to get my project to work. I would like to sample 3 to 5 analog signals using the ADC on the DevKit, followed...
A beginner's question.
I am using UART over BLE to send data out.
As codes below, ble_nus_string_send() works and continuously sending data out, with the Wireshark's...
I have some problem when I implemented 52832 dfu.
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio...
Hello i have a system that which i get data from a ultrasonic sensor and send it to Arduino UNO and nrfConnect application via the RBL Shield ( nrf8001 ) so i want to do it...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to use another nrf51422 board to update the previous board. Is this possible...
Hi All,
I have a problem where I cannot seem to wake up my NRF52832 with a GPIO. I am first attempting this on my NRF52DK with an interrupt form an accelerometer.
I...
Hi,
I'm trying to build a piece of firmware for the nRF51 DK, using the mbed OS 5 platform, but I keep getting a linker error from 'ld', using the ARM GCC 4.9 tools from...
Hello,
I want to build a list of available BLE devices and show the device names to the user via a display (pretty normal BLE search).
The search shall be done for devices...
Hello Everyone,
How could I use the temperature from nrf_temp.h in the Eddystone (TLM) example?
Eddystone (TLM) example:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral...
