Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
hi,
i am working on blinky example code. i was build the code and generated hex file using Eclipse IDE. i have nrf51822 ble module.
want to flash the hex file using dfu...
Most of the make files and project files within the nrf5 SDK contain a bunch of defines of the form -DNRF_PAN_XX. A search through the SDK v11.0.0 reveals only a few references...
I have included all paths of all (.h) files including (nrf_delay.h) however I got errors as seen in the photo. What do you suggest to overcome such errors?
Also, Is the following...
Hi,
This is very newbie, and I am stuck.
I am following to the letter the instructions to create the micro-ecc according to this instructions.
The problem, and it...
Hello,
I want to use packet length extension with the PCA10040 and SDK v12.
The peer will be the nRF51 dongle (PCA10031).
I believe that the nRF51 dongle doesn't currently...
I am still noticing a higher than expected power draw on my nRF52 and I want to make sure I have adopted best practice in turning things off/optimising things before entering...
Hi,
I am using a 128KB-rom 16KB-ram nrf51822 and trying to run blinky from SDK 11 with softdevice.
If I load nrf51 S130 1.0.0 softdevice, and use the following in my...
As of SDKV12, because of the removal of pstorage, I upgraded my app to use fstorage.
If you look at the SDKV12 doc at this link, you will notice that it is quite lacking...
Hi,
I am trying to write some data into the flash of the nRF52832 SoC, but can only write around 5 kb of data. After that I will get an error of number 7, which should...
I'm using SDK v11, nRF51
I started developing with S130, v2.0.1
The device is peripheral only, so I decided to switch to S110 v8.0.0, since I need the memory.
I made...
I don't have a particular issue right now, just a concern that I have because my device needs to be bulletproof when it comes to reset behavior.
When sd_mbr_command(SD_MBR_COMMAND_INIT_SD...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
Hello,
I'm developing nRF52 with Keil5.14.
Before I used nRF52_SDK_0.9.2 and it worked fine.(With NordicSemiconductor.nRF_DeviceFamilyPack.8.0.3.pack)
I upgrade the...
Hi all
According to the following post, the RAMONB register doesn't exist since the nRF51822 has only 2 RAM blocks: devzone.nordicsemi.com/.../
But the current version...
