Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Use SDK 10, SD version is 8.0.
I add the dfu to the ANCS project. Then use the nRF Toolbox App to update the firmware,
but it pop up "Read DFU Verion characteristic...
Trying to qualify our design with Bluetooth SIG.
What QDID's should I reference to generate a test suite for PTS?
NRF51422 QFN48
nRF51 SDK v10.0.0
SD 310
Hii everyone,
In a project. I'm trying to add dfu to a central and peripheral project. While doing I come to know that dfu using device_manger calls for its processing...
Hi,
I want to use the RSSI feature for CCA, i.e. measure background signal strength. The radio is started in RX mode, then I use the following code to get one RSSI sample...
Hello,
i implement the CTS_C example in my application.
I get the correct time Output in the UART.
Is this time the running in the Background?
How can i check if is...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
IN COMP of 52832, I find that a current source around the COMP form a OSC with a cap. I want to know what is the use of this OSC. And can the current source be disabled if...
I have a few characteristics under a service, and I'm trying to store the value if any of these characteristics is written to. However I run into an issue where if I enable...
Hi !
There is one thing I don't understand with the led included on the NRF51-DK board.
According to this thread ( devzone.nordicsemi.com/.../ and the datasheet it seems...
I want to take saadc samples for one second,every 5 seconds,the rest of the time the mcu is in system on sleep mode with rtc1 on.Eery 5 second there is an rtc event and the...
As the datasheet showing
The GPIOTE input mode consumpt upto 22uA ,it is inconceivable.I want use NRF51822 to design a ultra low power consumption production ,and use...
HI:
I want to use nRF24L01+ as TX, and nRF51 Dongle as RX. And I try to use nRF51 Dongle to just listen for the RSSI of the NRF24L01+. Is there any example or reference...
Hi, I am new to nRF51DK. I am following this tutorial shown below:
developer.nordicsemi.com/.../a00066.html
After I flash my s130 softdevice, I follow the file directories...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
