The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I have developed my prototype using the NRF51DK and now i am making a custom PCB.I currently use the On booard segger debugger to program the NRF51822.Also, i have ULINK2...
Hi all,
I have been developing a program on mbed using mKit NRF51822 and am now ready to move from prototype to one off production.
I am wondering after i create a custom...
I haven't used printf for a while.
Today I am trying to write some code for UART.
but it can only send the first byte of the string to the port according to the scope, then...
I have the nRF51822 beacon kit, using Keil uVision, downloaded the beacon app and all associated files. Compiles, but how to program the beacon board?
I've done two things...
Using nrf51822, Softdevice S110 V8.0 with SDK V8.0.
Sometimes after attempting to erase a pstorage page with pstorage_clear the firmware receives the NRF_ERROR_INTERNAL...
Hello,
I use pstorage to store in nvm some default values after first boot, and change those values via uart commands.
My cb handler looks the same as one in this example...
hello there i have three nrf51 dk. now in beacon code can we do like, when i upload same code to all three nrf51 dk, three will have different major, minor number. can anyone...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
In the spec TA is specified with a max of 85°C
I assume that this is the Max Ambient temperature and that the die temperature may be higher
Is my assumption correct?
may...
Still trying to get anything ta all to work on the nRF52-DK
I erased the chip
I flashed the soft device "soft_device_s132_v3.3.3" to address 0 and verified
built...
Hi!
We are having problems with pairing & bonding procedures with iOS devices.
On the peripheral side we are using a nrf51822 BLE module on which we are testing pairing...
Hi all,
2 days before we bought nrf52832 board.
in new board i can able to execute all peripheral example ( LED BLINK,button,uart,timer..)which doesnt need softdevice...
I'm trying to setup the RTC in the nRF52 to count with a resolution of 1mS. As the count has only a 24 bit value, I wish to clear the count every hour to start again.
There...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
