Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Is there any way to sniff BLE 6.0 packets and see the new content such as channel sounding? I am familiar with the nRF52840 Dongle as a sniffer in Wireshark, is there similar...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
Hi guys and gals!
I recently got Evelution kit nRF51822 and I'm working on custom application with SoftDevice s110 on Peripheral side. I was looking in "nAN-36" documentation...
Hi,
we have developed a product based on the nRF51822 using Nordic SDK v6.1.0 and S110 v7.1.0.
Now we are on production and we are obliged to use the nRF51822-QFAA with...
Hello! I'm trying to program nrf51822 like a BLE device.
I'm using QT Creator + GNU Compiler + Open OCD + STlink(debugger) to create and program.
If I choose "gcc_nrf51_blank_xxaa...
I have a program based on some of the examples which runs in peripheral and observer roles. When either role is running alone it works without issue but if advertising and...
Hi,
my task is to develop a "repeater" and I have three nRF51422 evaluation kits.
For example, one of them sends a file, the second one receives it and then sends it to...
Hello,
Using the "simple_uart_get_ with_timeout",I cannot receive a "frame" bigger than 6 bytes.
Why?
while(simple_uart_get_with_timeout(1, &UART_RX[receivedBytes]...
I have a simple app that send button press/release events to a smart phone. One of the buttons doubles as the wakeup button. I would like to qualify the wakeup button press...
The documentation for S110 v7.1.0 sd_nvic_ClearPendingIRQ implies that it works with any valid IRQ.
I find that (using S110 v7.1.0 with SDK 7.1.0):
sd_nvic_ClearPendingIRQ...
Hello,
I'm currently reading nRF51_Series_Reference_Manual_v2.1.pdf. On page 28.9.9 there is the UART CONFIG register documented. Two bits of configuration for the Parity...
Hi,
Tried to develop an application to read current time characteristics from central device (ios app) by using nrf51822 peripheral device(s110_nrf51822 v7.0.0.). After...
Dears,
There is a problem as the subject. I am using the reference code of ble_app_hts to add an app timer for a service. the device of nRF51822 can be searched and connected...
Hi,
I'm really new here, sorry if it is a beginner question.
Our company wants to start developing a RTLS (Real Time Location System) to track mainly person (patients...
There are a few threads on using the AES module and there is a lot of confusing and somewhat contradictory information.
I want to do the following:
generate secure...
Hello,
i have an application that sends periodically sensor data from one sensor network (6 sensors - 16 Bytes) to a host f = 1/4 - 20 Hz.
I read the s210 and s110 SDS...
