NCS 3.0.1 MCUBOOT nRF52840
I am adding MCUBOOT to the coap_client example, which inlcudes snippets in the build configuration (ci, debug, logging, mtd). The snippets are...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
I didn ' t use an external 32 . 768 crystal , the internal NRF_SDH_CLOCK_LF_SRC 0 I used。
NRF_SDH_CLOCK_LF_SRC 0
NRF_SDH_CLOCK_LF_RC_CTIV 16
NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
iOS device uses random private resolvable type changes own bluetooth address address every 15 minutes as long as I know. Can I see the transittion just to change the...
I see the python S110 bindings (via SWIG) have been made; it was pretty easy to get the demo code up and running, many thanks! Any chance that S120 central role bindings can...
I have a custom board with an nrf51822 device. I also have Keil 5.12 and a ULINK2 and would like to program softdevice hex file into the nrf device. I have followed all of...
I'm trying my best to get started w/ the nrfgo 51822 development kit that I got last summer, but I'm just having a hard time jumping in.
I was a little disappointed to...
I need to use a high speed PWM (> 500 kHz) in which I can vary the pulse width. In examples, it's handled in software which is too slow.
Is there any way to set a pin on...
Hi,
I am having some problems getting the s110 SoftDevice working (sd_softdevice_enable stops the program execution) on a custom PCB. I have seen several issues similar...
Hello,
I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated...
I'm interested in getting started with NRF51, but the full DK is quite expensive here and I don't need it. Does the nRF51-Dongle sku come with a key for downloading & using...
Hi,
Can someone tell me (definitively) what the max SPI clock speed is?
I have seen 2,4 and 8Mhz here and in recent documentation and I'm confused.
Thanks
Hi
I have been experimenting with encryption and bonding and I think I don't understand completely the bond procedure.
To bond a device, it is necessary using the bond...
HI ,all !
I have a question about PORT event function.
as the 4 channels of GPIOTE (channel0 to channel3 ) have been used for other usage.
i need to use a general IO...
The only documentation I can find for s120 is part of the nRF51 SDK . Though it isn't clearly stated the SDK assumes release 1.0.1 of S120 is being used.
The v2.0.0 S120...
Hi
I got some questions about KEIL MDK uVision5.12 PACK.
I tried uVision5.12 PACK to install Nordic SDK package. Currenly, their latest version is v7.1.0.
If...
Hi,
I get 0x2001 error in spi_master_close() at the following 2 lines.
/* Disable interrupt */
APP_ERROR_CHECK(sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type));
...
