Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Is there any way to sniff BLE 6.0 packets and see the new content such as channel sounding? I am familiar with the nRF52840 Dongle as a sniffer in Wireshark, is there similar...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
It seems that is not possible to rewrite data on a block ?
I want to persist some data. The first time (after erasing all the flash memory) I store a data on a block, it...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Hi all,
I noticed that there are some instructions for testing keyboard on win8.1 or USB dongle.
Can I test it on my iPhone5s which is iOS7.0.4 now?
Regards,
Aaro...
when I use nRF51822 ESB Protocol,I set retransmit delay = 600us,anything else is working
good,communication is very well,but the minimal Tx period is 1.2ms,not 600us,why...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
I want to generate a pulse signal with PPI, timer2 and gpiote. But it doesn't work. Anything wrong with my code?
void init_timer1()
{
NRF_TIMER1->PRESCALER = 1;
NRF_TIMER1...
I'm working on a product that integrates an nrF51822 talking over SPI to an external display. The display protocol involves a series of alternating 10 us sleeps and SPI sends...
Hi,
Is it possible to skip a advertising channel by maximizing the advertising interval?
I can measure the current consumption of my device through CRO as specified in Evaluation...
My code:
uint32_t err_code;
uint8_t randomBytes[6];
err_code = sd_rand_application_vector_get(randomBytes, sizeof(randomBytes));
When this function is called...
Dear Sir,
What is effect, if I change the Heap Size from 2048 to 1024 in arm_startup_nrf51.s file?
On my project, my device (nrf51822) connect iphone with ANCS, sometime...
Generic Access (0x1800)
General Attribute (0x1801)
can them be removed? if they can't be removed, can we use it instead of customer service? my purpose is to reduce advertising...
Hi,
is there a function that returns free or used memory of the BLE SD? I'd like to know how much memory is allocated for added service and characteristic and make a guess...
Hi I'm looking to Program the NRF9E5 RX board so that the LED remains high until the switch is pressed on TX. So the TX button would turn the LED high and remain so until...
Hi,
How can I use nrf905 with an Openwrt based module? Are there any driver for operation systems? These modules have many gpios.
Openwrt based modules are simply Wifi modules...
Have anybody a solution for my problem ? nRF24LE1 is first in low power state (PWRDWN is 3 or 4) and wakes to send a message. Mostly the message has the same PID identity...
