hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
When the central and peripheral is connected, we can get the RSSI value through sd_ble_gap_rssi_start() function. but how can I get the RSSI value when not connected (scaning...
Update: I've worked on the BLE arduino sdk from Nordic, and followed all the directions, but I'm having some compiler errors. I've crossposted to a different forum for more...
I am using pstorage library to keep some data in NVM.
Should I use some nrf_delay calls while using pstorage_clear()?
I am calling pstorage_store from callback function...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
From the documentation for the sd_ble_gap_sec_info_reply() function,
"This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times...
Dear Madame/Sir
From my client I received nRF51822 DK.
See att file.
I do not see Product Key for DK
How can you solve the problem ?
Redards
Valeri Tosev
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
