I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I've made a modified version of the example DFU provided with SoftDevice v7.0.0-3 alpha that works in single bank mode instead of dual (because I need to bootload a huge app...
Hi all !
I have been working on an nRF51822 based board for a little while, the ten 1st prototypes worked well so we asked our factory to make 20 other with the same design...
Hi All,
Is the lite programmer which comes with the nRF51822 Development Kit sutable to program my code into nRF51822-Beacon?
If yes what cable would I need (supplier...
Hi,
I'd like to read PnP and the system ID from Device Information Service.
How can I initialize system and PnP ID? Are there any examples how to do this for nrf51822...
Hi,
I'm calling sd_ble_gatts_hvx and every once in a while I get an error code of 0x3401. I went through the SDK documentation but I could not find what that error code is...
Hi,
I have a peripheral device that needs to connect to both Android and iOS phones. Depending on which type of phone it connects to it is required to perform different tasks...
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
Hello!
I need more battery life and higher resolution in my applications. That's why i need to level down the signal power, if it is possible. Thanks in advance.
Hi,
I'm using nRF51822 Bluetooth Smart Beacon Kit. Is it possible to to switch between
beacon mode and configuration mode without the need to press SW2 button e.g.: by...
How do I keep advertising when I have a connection come in? I'm a BLE peripheral.
I'm running SD 7, is there a particular flag or sequence I need to do now that I've upgraded...
Hey!
I'm testing out the new SoftDevice and am trying to update firmware OTA but thus far have not been able to do so. I've tried from the Master Control Panel android...
I'm using NRF51822 as SPI slave and STM32 as SPI master. Everything works fine except the first SPI transaction after resetting both boards.
On the first transaction I...
Hi guys,
I'm curious whether or not i can try the mbed platform on the EK board. The circuit of the mbed kit and the EK look pretty similar. All the LEDs and buttons are...
I'm using the NRF51822 - I've just started a project. I can build and load it into my target board. I enter debug mode, and I'm able to do step through the code, add breakpoints...
