void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using nrf51822 evaluation kit with ble_lbs (Led button sample) profile, I need the USB dongle source code for ble_lbs (Led button sample) profile because I...
Hi,
Is it possible to change the advertisement parameters of a beacon device without connecting to it?
(ex: major,minor value & interval)
Is it OK if our beacon product...
I use ble_app_uart demo of pca1001 and my SDK version is 5.2.0. I want to use APP_BUTTON_INIT to handle a button event. So I changed the buttons_init(void) like this:
static...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
Hi everyone, I don't have the nRF51822 yet, but still want to get familiar with it as much as possible before I get to buy it. I was looking for a description of the functions...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Has any managed to connect a Windows Phone 8.1 device to NRF51?
BLE is "definitely" supported on Nokia Lumia:
Nokia Support
But I am unable to pair with either SD 5.1...
I'm working with a custom hardware board made by hand which works properly, but since we make a batch with a pick and place machine, something seems to be wrong with the board...
I am trying to use the S110 v7.0.3 with a nRF51822 QFABA0 chip. I am using the hrs example from the SDK v5.2.0 ( I have changed the IROM address to 0x15000). I've got an error...
