Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I would like to ask you some questions on nRF51822 Hardware:
From nRF51822 datasheet, a 16M or 32M external clock is needed, now if we have one 26M TCXO is available...
Hi
Maybe you can help me.
I'm trying to get Device Manager to work, but I'm having several problems. Although the Device Manager is being correctly initialized and the...
Hi, I am developing a project under Eclipse Kepler & Mac OS X;
The project
When i debug, and set a breakpoint in the main.c, I got this message:
Then after Steping...
hi, i'm new in nrf module, i use nrf51822, i'm totly confuse what voltage that i should apply on DCC pin? if i want use internal dc/dc than what the voltage and if i use LDO...
after setting BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, I getting BLE_GAP_EVT_SEC_INFO_REQUEST event,
I am using same code as the sample:
case BLE_GAP_EVT_SEC_INFO_REQUEST...
Hi
I am using v6.0.0 softdevice S110 and SDK 5.1.0
In nrf_soc.h the function sd_temp_get() is defined.
The comments there say ..
"p_temp Result of temperature measurement...
Hi,
I use ble_s110_serialization sample code.
I try to notification many 20bytes(total 5KBytes) to my phone, I add some code in ble_app_hrs.
I follow this link to...
I used nRF_Demo_Utility ios app and WFConnector.framework in a sample testing app im building. And when I tried to archive it using xcode it invalidates it with a error message...
Hello,
I’m porting the hids_keyboard demo to work with the nrf51422 dev board. I just changed the #defines for the board in project settings, as well as the pin assignments...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...
Hi folks,
I am struggling a little bit with Eclipse.
I just followed this tutorial ( embeddedsoftdev.blogspot.ca/.../eclipse.html) , the project compiles fine, but sometimes...
