We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...
This question is a follow on to https://devzone.nordicsemi.com/f/nordic-q-a/38085/how-to-create-a-copy-of-examples-project---segger-embedded-studio .
It's clear that making...
Hi,
Can i use nRF52840 Pre Development kit as a sniffer.
Also can i use it to program my customized PCB
Note: I need to do both of above urgently so i cannot wait to...
nrf connect sdk version :1.2.0
application:nrf_: desktop
I use command " west build -b nrf52840_pca20041 -d build_pca20041" , but it report error at last.
I don't know...
Hello
Currently, there are systems that operate with peripherals developed with nRF52832, SDK v.12.2.0. I have a question about supporting this for meshes.
1. Are you...
Hello,
I am trying to send a rather large HTTP payload from the nRF9160, the payload is about 10KB in size. The problem I am running into is that after about ~4KB of data...
I'm actually building a project that need to communicate with sdcard.
i read a lot about that and i'm very confusing when i passed on nordic sdk lot of code and ressources...
Hi all,
I am working on a project which uses a vibration motor. I want the vibration motor to vibrate with different patterns. I have read online that a 20kHz PWM can be...
Hi,
I've found this answer which states that the NUS throughput is around 2-4 kB/sec.
https://devzone.nordicsemi.com/f/nordic-q-a/27044/ble_uart-demo-throughput-is-very...
Hello guys
I am trying to compile the latest nrf sdk with version v1.2.0 it fails with the following error
but when i compile either v1.0.0 or v1.1.0 it is successfully...
Hello:
I am using the QSPI example on the NRF52840 dev board with the objective of implementing SPIFFS. After a lot of tinkering I believe this is not possible due to...
My PC is windows 7 64-bit. I use SDK16 with softdevice. I am porting CDC code to my application as follows. It has 2 issues. 1st: It will cause hardfault if I call the function...
