I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I have been implementing the GPS on my thingy:91 with the firmware v1.2.0
I'm able to do a cold start and get a FIX is if in do not move the board for around 100...
Hello，I am using SDk14.1.Sometimes w hen I send data to nrf52832 via serial port，the code prompted me "APP_UART_COMMUNICATION_ERROR".And t he value of the ERRORSRC register...
Hi, I am trying to perform an OTA DFU of SD + BL on nRF52840, upgrading the SoftDevice from 6.1.1 to 7.0.1.
I have been able to do a DFU of application only, and it works...
Hello everyone. I have the following issue: I would like to connect some Nordic Thingy:52 nRF6936 devices in a mesh network, using the application nRF Mesh . In theory, the...
Hi,
We are in the development stage of a project using NRF9160. We would like to know which one is the stable version of NRF connect SDK. In the , git we can see tags like...
I have a non-secure app targeted at the nRF9160-DK platform and use SPM as the secure app. I can apply a device tree overlay to SPM to enable peripherals from the non-secure...
Hi,
We are creating an application that requires LTE connectivity, GPS and communicating to a server using HTTPS. We used the HTPPS client example as a starting point and...
Hi,
I'm quite new to the nRF environment and am trying to run one of the nRF5 SDK examples (ble_peripheral -> ble_app_uart -> pca10056 -> s140) on a custom bord with BT840...
Hello everyone, I have a problem I am trying to merge to project using I2c and Uart, So I copy the code from the uart example in the sdk.
I can read on the debug terminal...
Good afternoon, I am trying migrate from ARM compilar 5 to 6 some examples of the SDK 16, but i have some problems with it. I was wondering if a version 6 compatible sdk would...
Hi
I am using the provided example ble_app_queued_writes to send 256 bytes in each call.
It is taking around 13 seconds to transfer 3136 bytes:
12 calls of 256 and one...
Hi,
My project is currently using NRF52832 with Mesh 4.1
After update from SDK15.0.0 to SDK17.0.0, everything just works fine except my button.
I am using P0.18 for...
Hi,
currently we are developing a firmware for 52840 based on the nRF5 v.16 SDK with Softdevice 7.0.1 on a custom board. We are able to connect and bond up to 5 devices...
