Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Base BLE structure ble_advertising_t contains a member structure ble_adv_mode_config_t. This structure contains two parameters that are meant to limit number of advertisements...
Hi Team,
I want to create on flash section to store the specific data like Crypto Keys and Serial numbers. How to create one page/section in existing Flash memory without...
I am trying to test a BME280 sensor on the nRF9160. I followed the steps where I created a folder (board) and added the nrf9160_pca10090.overlay and add couple of line in...
Hi, I would like to implement free rtos on nrf 51 using IDE Segger Embedded Studios. Could some one please direct me to the necessary links/ information.
I have researched...
Hi ,
I am working on project which is based on nrf9160 Development board.
could you please verify these points-
1. I am sharing the snapshot of the registers...
I have downloaded the Keil compiler and the Nordic key for same.
When running Keil_v5/UV4/PackInstaller.exe I can not get the update:
Cannot download file developer.nordicsemi...
Good Day,
i´m want to use saadc with 7 channels. I´m using the ADC Driver with an interupt handler. All 10ms the sampling starts per cpu. I use the configuration followed...
Hello,
I am running on a NRF52840 DK a Zigbee program configured as a router. For the coordinator i am using the cli example from the SDK.
On the router, I have developed...
Dear Nordic Semi, ladies and gentlemen!
I'm working on a prototype device with USB host functionality. I am using Arduino USB Host Shield connected to nRF52840 DK . DK is...
Hi，
We want to confirm the effect of GPS fix_interval and fix_retry, so we start GPS with parameter fix_interval=10s, and fix_retry=30s, then get the result as the following...
I try to bonding.
Using SDK 15.3. 0 and S332 Softdevice.
I successed bonding procedure used Peer manager.
after bonding, If I try to connect one more, nRF Connect app...
Hi, I can not connect to nRF52833 and nRF51 after I return from Flight mode on Android devices. I am keep getting Error 133 (0x85): GATT ERROR. I am using the nRF Connect...
Hi,
My device advertises and "connects", but then I later receive an error through nRF Connect: "Error: Received a GATT Timeout".
Has anyone else had a similar problem...
Hi.
I get Linker error when i compile 'iot_secure_dfu_bootloader_secure_dfu_s132_pca10040' example from SDK 16.0.0.
The compilation passed (although i had problem with...
