Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi I programmed the nRF mesh experimental dimming example on the nRF52832 chip. I noticed that, when using Bluetooth Mesh provisioning apps (I've tried several to verify this...
I am trying to setup a PPI channel to trigger the SAADC in simple mode. However, it appears as though the SAADC module is disabled after every read. I.e. if I write:
...
I am unable to flash the DK board facing issue " Failed to Connect to Target. No idcode detected. Please check connections and Target interface Type."
DK Board Details:...
I am using LSM9DS1 IMU, nRF52840 with SDK v16.0.0. I configured the IMU to raise an interrupt when the FIFO buffer be full by writing to register INT2_CTRL the value '0b00011000...
I can't see it!
https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Connect-for-desktop
The 'Downloads' section contains only the "host" native app - doesn...
I am trying to interface the BMM150 magnetometer with the nRF58240 MICRCONTROLLER, Iam able to establish the I2C connection and get the return value from the reg 0x40 and...
The stock LPN client for Mesh SDK v4.0.0 throws NRF_MESH_EVT_SAR_FAILED when replying to a publication set message via a friend node.
All code, reproduction data and log...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I want to write Serial number into...
Good morning....
I have an application that needs a remote control to communicate to six end nodes that are about 200' away in warehouses. It is a one-way communication...
Hi
the latest Errata sheet of the nRF52840 lists number [228] RADIO: No interrupt is generated for SYNC event.
Checking it, I was a little bit surprised finding actually...
i am using BLE template from examples BLE Peripheral and adding some custom characteristics and not changing any advertisement data. But the device is advertising with only...
Hi,
I want to set up visual code studio for development. I was able to successfully run the blinky app on PCA10040 board and also emulated PCA10040e example.
After this...
Hey folks,
I don't know what's the problem but I am really struggly to implement a simple UART into my heavily modified BLE Multilink Central Example (SDK16)..
Maybe...
Hi,
In my application, I would like to transfer data from MCU ---(UART#1)---> BLE#1(Peripheral) ---> BLE#2(Central) ---(UART#2)---> PC. I start my code based on ble_app_uart_pca10040e_s112...
