We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
Looking to put this into our new consumer product, and working with a CE/FCC lab. They would like pre-qualification documents if any. I just need to know if they exist and...
Hello, I would like to copy ble_app_uart_c example to a seperate folder and work with that independently. I looked into the following thread and changed my include paths....
Hello
We produced and assembled our own board based on nRF52832-QFAA chip.
It works fine but we want to improve the performance. We heard at the past that we can provide...
To save energy, we want to sent connectable packets infrequently, say once every 10 secs. We also want to send some status info more frequently (once per sec) using non-connectable...
Hello. We are an OEM design company that is in immediate need for a BLE solution that will be compatible across the assorted phones in the market. Very new to BLE and only...
I am developing an application using Nordic SDK 8.1 for BLE that requires a low power consumption. To lower the power of the slave BLE device I was able to lower the advertising...
Hi,
My board env as below:
nRF52832, pca10040, SDK14.2.0, S132
I am trying advertising sample according to the tutorial
devzone.nordicsemi.com/.../
The "Address...
Hi,
I'm trying to build and install my first code that uses the BLE / softdevice to my NRF52-DK
I'm using Windows 10, Eclipse/gcc and nRF5_SDK_14.2.0_17b948a I'm able...
On my peripheral I filter the devices connected and refuses them when not bonded.
When a device not bonded tries to connect to the peripheral, it forces the disconnection...
Hi,
I am using nrfsdk11 nrf52 and s132 soft device. In my code,I am doing this in main();
void fs_evt_handler(fs_evt_t const * const evt, fs_ret_t result)
{
if (result...
hello sir,
i am using ble mpu example and it working fine now i want do send some commands from mobile to nrf52832 chip via these commands my application should work.
...
Hi everybody,
I will to use the nRF52832 QFAA for a drone, and I carried out this schematic for this chip.
I have two questions :
For the capacitor C6, which value should...
I'm trying to start my app from the bootloader, which is funcionally basically the same as the one in nRF5_SDK_11.0.0_89a8197.
To start the app I call bootloader_app_start...
