Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Feature request.
In the current Connect SDK, I must add the name of any new 9160-based board directory to ncs\nrf\cmake\multi_image.cmake.This requires anyone installing...
I am making a simple device based on nrf5240 - I want to control the servo from a smartphone. I used the WART and Blinky examples as a starting point. The data exchange algorithm...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
Hi!
I have written a driver for Dali (prototocol used in lighting management system) on nRF8240. It is a baremetal application which uses the SDK of Nordic (the drivers...
While it's easy enough to download the SDK from Nordic's website, it's a slow and painful process.
It's slow I assume because the site is hosted far away from me. Loading...
Hi!,
I am trying to use one of the analog inputs for reading the voltage using saadc.
Since a don't have a battery now that is about 3.5V or less, I decided to use one...
Hi, I am trying to create a custom board and add it to the zephyr app. Currently, I have added boards/arm/irnas_izoramv21 file to my application folder. When I am building...
Hi
I am using nRF51822, S130, SDK12, Working on adding static key security to my application
So far I have change the GLS (glucose) example to static passkey and connected...
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
