Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
I am trying to program a BMD-300 over a serial connection through the RigDFU bootloader. The module has been updated to the latest factory image.
I can compile the application...
Now I want to run the python scripts interactive_pyaci.py in Embedded system device, I want to know which version of Python Environment must be install in the Embedded device...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...
Hi, I am using the Serial port library in SDK15. I am using the port in NRF_SERIAL_MODE_IRQ mode. After transmission the number of bytes receive are variable ranging from...
Hello. Im working with:
sdk14.2
softdevie ANT_s332_nrf52_5.0.0
chip: nrf52832
Problem: we have a product almost ready to be sold. We decided to start the migration...
Hello. I am trying using the nRF52832 with SoftDevice S132 v4.0.2 and SDK v13.0.0 along with the uECC.c/h files that I downloaded from github.com/.../micro-ecc . My device...
I know you can configure the threshold for low voltage that would stop writing to flash.
some people set this to 2.7 volts.
I want to know what the minimum voltage the...
I have followed the exact steps mentioned here http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v2.0.1%2Fmd_scripts_interactive_pyaci_doc_demo_configuration...
Hi all
I use nRf52840 with SDK 15.0. It allows SPI SPIS and TWI (i2c) ,but almost 3 items in the same time. I want to use spi0 as master to configurate my other mcu and...
Hi everyone!
I'm trying to write demo application to evaluate how custom services would work on nRF52840 SoC. Problem is that iPhone ( iOS 10 and iOS 11 ) doesn't show device...
Actually refers to the mobile version of nRF Connect but it's not on the menu.
I have inherited a legacy Android app that connects to various BLE devices and reads data...
Hi Nordic Devzone,
Now that I got my Thingy52 running I am wondering if there are any examples of the thingy52 connecting with a nRF52840-PDK or something of the sort ...
