Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello nordicers,
I'm stucked with long writes (android central to nrf52 peripheral)
I'm using SDK 12.3 and S132 v300. Android as the client central (RxAndroidBle libary...
Hello,
I ported nordic heart rate example to nuttx. I have peer_manager_init() in my codes.
After programming the device, I can connect and bond when I issue "nrfjprog...
main.c I'm using S120 softdevice with nrf51822, I want to use S120 as central and peripheral devices.
When I received my beacon data then switch to peripheral for advertise...
Hi!
nRF52, SDK13, S132.
I work in central mode and need make
ble_nus_c_rx_notif_enable()
But in the code drivers I only have tx function. In a SDK9 for nRF51 I...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
What I am trying to accomplish is to establish a connection between an iPhone (device 1) and an NRF52 (device 2), then sniff the data sent between them from a third device...
Hello,
I have designed a custom board with NRF52832 IC which controls vibration motors. And I am turing on vibration motor from n-channel mosfet as shown in the image below...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
On a custom board with an nRF52832, I have some LEDs I'm driving from the pins 9 and 10. One or both of these pins are used for the NFC antenna unless you configure them as...
I am trying to understand the whitelist feature by following the HID Key board peripheral example on S140 v5.0.0.-2_aplha on nRF52840 dev kit. I am using iPhone SE with nRF...
