hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
Hello,
I am trying to send out a notification and getting this error code 13313 (in decimal, 0x3401 in hex). Which eventually leads to BLE_ERROR_GATTS_SYS_ATTR_MISSING...
I developing applciation based on nrf51822, sdk11. I have read several posts about using app_timer_cnt_get() and get only 0 value. As far as I understand, this is because...
i want to connect my nfr51822 device to only one phone( that means which phone was connected first). For this purpose i enable whitelists but i create whitelists nothing has...
In timer example in sdk 11, I replace the Timer 0 by timer 1 and timer 2 but the LED did not blink. Can you guys please guide me through this? In nrf_drv_config.h I have already...
I have Keil uVision-5 and loaded the legacy patch. However Nordic NRF51 does not appear anywhere as an option. The Project loads fine and compiles. However, I cannot use the...
nRF52862, SDK 14.2, SD 5.1.0,, Arm GCC (Eclipse)
I have a custom service that is working well when 1 device (phone) is connected. All notifications are sent properly to...
Hello everyone,
I am trying to add new service into ble_app_uart example. I compile successfully. I do not get an error. But the device is not advertising. I can only advertise...
In my plan, I have used NRF52832 IC as the transmitter and the NRF24LU1P+ as the receiver. I have tested the wireless transmission successfully. In order to reduce consts...
Hello,
I get the sources from Thingy Mesh Demo and use the guide to build it examples. Thingy_node build without errors, but Thingy_bridge return the error "too few arguments...
Hi
I am using nrf52832 doing a project and I 'm new to this MCU.
My project concerns sending data from APP via BLE to nrf52832 to config parameters of SPI (data and clock...
Hi,
I am trying to modify the multilink central example to send string to other board (peripheral)
I already did the UART configuration and in my tests I saw that when...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
We are trying to modify the nRF Beacon example app for iOS that Nordic provides. We are unable to get app to see the devices from the iBeacon kit when they can be seen from...
