Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I cannot find the call to sd_ble_gap_appearance_set(...) function in the ble_app_blinky example, so that I think it's unnecessary to call:
in nRF5_SDK_for_Thread_v0.11...
Hi!
I am using UART in NRF52832 with SDK15.0.0 to communicate with TCP socket via cellular modem.
I am using printf() to send the following AT command sequence to the...
Hi, I am using the Serial port library in SDK15. I am using the port in NRF_SERIAL_MODE_IRQ mode. After transmission the number of bytes receive are variable ranging from...
Hello. Im working with:
sdk14.2
softdevie ANT_s332_nrf52_5.0.0
chip: nrf52832
Problem: we have a product almost ready to be sold. We decided to start the migration...
Hello. I am trying using the nRF52832 with SoftDevice S132 v4.0.2 and SDK v13.0.0 along with the uECC.c/h files that I downloaded from github.com/.../micro-ecc . My device...
I know you can configure the threshold for low voltage that would stop writing to flash.
some people set this to 2.7 volts.
I want to know what the minimum voltage the...
I have followed the exact steps mentioned here http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v2.0.1%2Fmd_scripts_interactive_pyaci_doc_demo_configuration...
Hi all
I use nRf52840 with SDK 15.0. It allows SPI SPIS and TWI (i2c) ,but almost 3 items in the same time. I want to use spi0 as master to configurate my other mcu and...
Hi everyone!
I'm trying to write demo application to evaluate how custom services would work on nRF52840 SoC. Problem is that iPhone ( iOS 10 and iOS 11 ) doesn't show device...
Actually refers to the mobile version of nRF Connect but it's not on the menu.
I have inherited a legacy Android app that connects to various BLE devices and reads data...
Hi Nordic Devzone,
Now that I got my Thingy52 running I am wondering if there are any examples of the thingy52 connecting with a nRF52840-PDK or something of the sort ...
Hi every one
we are working now on android application that use ble communciation, we aim to use L2CAP in lieu of GATT protocol but we can not find any exempl of lt2cap...
Hello,
I have a nRF8001 Development Kit and I have some problems to get started with it.
I want to use the PCA10000/nRF51822 Development Dongle with my laptop and the...
Development Information: 1. We use the development board PCA10040 provided by the distributor; 2, example:nRF5_SDK_14.2.0_17b948a\examples\ant\ant_plus\ant_bpwr\bpwr_tx; 3...