hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi, I'm using nrfUtil 10, which is a bit old. I'm trying to generate an init packet for DFU but the tutorial was for newer versions of nrfUtil only and a lot of commands appear...
I tried to compile the sd card example from the fatfs library. But it didn't work.
Can anyone tell me more about this errors?
NRF_BLOCK_DEV_SDC_DEFINE(m_block_dev_sdc...
NRF52DK (PCA10040) - SDK14 - Arm GCC (using Eclipse) - S132 5.0.0 Soft Device
I had a custom service set up in SDK13 using the tutorial here .
I am migrating my project...
Using nrfjprog version 9.7.2 on Windows 7 Professional. Just discovered that when .hex file is read-only, nrfjprog fails.
>nrfjprog --verify --program app.hex Parsing hex...
Hi,
I migrated an nrf52832 s132 application from SDK12.2.0 (sd v3) to SDK13 (sd v4.0.2). On the iPad and iPod Touch the NRF Connect app does not discover the services I...
Dear Nordic Semiconductor team,
I just wonder if BLE is suitable for energy harvesting topic?. I want to ask if your ASIC need permanent power supply? An idea behind is...
I am trying to build the mesh-bootloader and the cmake build system throws some error, could You have a look at my comandline options, or say what is going wrong.
I am using...
Hi
I want to make a dongle which can connect to and communicate with HID .if the peripheral is a HID(eg gamepad ,consumer or mouse ),the central device how to communicate...
Hi,
This is just a quick check of my understanding of the interrupt priority levels on nRF51. I read up on the documentation I can find.
I'm assuming that I will receive...
Hi,
I am designing a custom PCB with the nRF52832, I am going to use wire bent antenna over it. Can I bend feed wire by 45 degree. I have attached image for the part I am...
Hi All
I am using the example of uart in SDK10 wit nordic 51822
First of all ,I add a PA with 51822 to increase the signal of BLE, but I notice that the speed of PA is...
I can read peer address and rssi field in the scan request report. But how can I read the AdvA address field in the scan request to make sure that the scan request packet...
Is there a method to remove a node from the network using the current bt mesh stack? I've looked through device_state_manager.c but it appears to me that there are only functions...
Hi,
I am using 2 nRF52840 DK to build a network, One is the client and the other one is the server. Both of them are connected to computer with USB cable.
I would like...
hi,
i test my project for i2c sensor module, the debug found have error what there are the following error tips.
..\..\..\swct_application\i2c_sensor_driver.c(14): error...
