Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
As I don't know much about audio,I have trouble with the gain of the pdm module in nrf52832.Now
I have used MP45DT02 as the digital microphone,but I just can't understand...
Hi, I've searched and googled through this site and made sure no one asked this question before.
In core\Bearer_event.c, there is this function:
bearer_event_flag_t...
I'm trying to connect two nRF5 devices together, Central and Peripheral, and use a custom BLE service that I have written that has a custom 128 bit UUID.
I'm in the process...
Hi,
We are sending a data using Nordic UART Service (NUS), the data is transferred over BLE as a Indication.
From Message Sequence Chart in Nordic Infocenter
Here...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
I'm using nrf52832 in my peripheral device, I want to secure its connection via any authentication is there any method for that?, also I need to encrypt its data(characteristics...
Hello,
I'm working on a bootloader based on the examples in SDK 13.1. As we have expanded its functionality, I'm now wondering what happens when one of the steps in the...
Okay this got us going around in circles and it looks stupidly simple. It seems there is a knowledge gap since we saw many posts similar to ours but without clarity as of...
Hi,
I am getting data over thread and BLE network. I want to send the received data over uart.
Is it possible to use serial example to merge with thread server example?...
Hi,
We are having problems trying to integrate support for maintaining application context and bonding info across firmware OTA updates on our NRF52 (nRF52832) based board...
I just test nRF52840 DK with ble_app_att_mtu_throughput_pca10040_s132 example. I know BOARD_TESTER transmits 1024 dummy kbytes to BOARD_DUMMY. I want to replace dummy byte...
I am working with the throughput example for the nRF52840 demo board.
I have found all sorts of control structures which include the counts of bytes sent.
I have not found...
