Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
sdonly.zip softdevice.zip Custom board with a nRF51422, SD 310 rev 2.0.0, nRF Toolbox rev 2.4, iOS 8.4
When trying to use the DFU app to update my softdevice and/or the...
Unless I am not understanding the code correctly (highly possible...), once the bootloader has restarted into DFU mode, no bond is required to upload new firmware. This works...
Can I have "nrf toolbox" source for android eclipse?
I can just find the source for android studio not eclipse.
because I can't use android studio now, I need the source...
Hi all,
I've just started working with the nRF24L01+, and I've come across some issues when attempting to do an initial read from the datapipe 0 RX address.
After reset...
I am in the startup phase of a uni-project and I would like to ask you about the feasibility of using the nrf24L01p with power amplifier as the radio module. Specifications...
Dear all, I'm trying compile github ble example ble_app_hello_world for Nordic nRF51422 following steps on Tutorial Advertising for Beginners and found 6 errors all same type...
Hello,
I am using enhanced shock burst as communication protocol. Currently i am using rtc 300us timer to call nrf_esb_add_packet_to_tx_fifo() to transmit data every 300...
I have a custom board with the nRF51822 chip, the chip is set-up with the recommended (CFAC WLCSP schematic with low voltage mode) setup, excluding the external low frequency...
Hi,
I just finish designing my board and soldering it using the Bluetooth low energy nRF51822 chip and i want to test it.
i want to know if i put the coin cell 3v and...
Is the ECDH encrypted key exchange supported on the new S130? If not, when can we expect it to be available?
I am surprised this is not given a higher priority, since now...
I use s110 v7.1.0 ,nrf51822qfaa.
now I find the pstorage_store work is OK if I is not run sd_ble_gap_adv_start function.
but I fin the pstorage_store work is wrong if...
I use s110 v7.1.0, nrf51822qfaa.
The write flash data using pstorage is OK ,before ble_advertising_start() function is start run.
But if I run the ble_advertising_start...
Hello,
I am using the nrf52pdk and am wondering if there is a way to force an output compare interrupt to occur. For example, lets say you want to generate an interrupt...
