در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
is it possible to use this module from LAIRD in connection to the nordic SDK - i installed the softdevice hex but the hrs example for s110 is not running properly ...
Hi.
My nRF51822-mKIT, when attached to the USB port, don't flashes the green LED nor the drive appear on Windows explorer.
It's possible that mbed loader was corrupted...
I have found that when I try and initial the Softdevice to use the Scheduler, shortly after initialization and right before dm_init() runs, I get an NRF_ERROR_NO_MEM error...
Hello,
I am trying to use nRFUart project given with the Master Emulator API, however; the original code crashes while trying to initially reset the hardware device. I...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
I'm implementing a Eddystone beacon ( github.com/.../eddystone ) with the 3 specified frames and it works quite ok with changing the advertising data before transmitting by...
Hello,
I am trying to use the new bootloader provided in SDK v6.1.0 with SD v7.1.0 and MCP v3.7.1. I have loaded the unmodified project from nrf6310/device_firmware_updates...
Hi,
In order to use new nRF51 SDK v. 5.1.0, we have just bought a new NRF51822 EV Kit from your distributor. It contains PCA10001 v2.2.0 2013.49 but the IC is nRF51822...
I am trying to pair nordic with an iPhone app. (using lightBlue) but not device_manager_evt_handler is not getting called
Here is the code, Is there anything else that...
Hi,
i need select bluetooth chipset,but it should support options below;
-Minimum baud rate should be 300 bps,
-It should support 7,8 data bits,
Which can i choose...
Hi
I try to write an application in C# with the MasterEmulator dll (Version 2.1.12.6). It works with the dongle, but not with the nRF51-DK. I can open the Device but I...
Hi,
I am planning to use nRF52832 for one of our projects. Can you please help me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards, Yaron
I've just started working with Nrf51822, I'm trying to make this scenario for weeks but i failed.
Plz help me!
How to make Nrf51822 wake up by a button click, increment...
