Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
Hello!
nRF52832 IC supports programming OTA the first time after its soldered onto a custom design?
We are designing a very small form factor wearable product and would...
Hello all,
I have a few questions about the best way to go about mass producing nRF51822-based devices.
Can anyone recommend a manufacturer that possesses the...
Cruising through a few questions about the ISP, In System Programming, in the forum and in both the specification sheets, 1.0 and 1.1 there is no clear documentation to the...
Dear Nordic members,
I am currently trying to measure the power consumption of the nRF52832 with the nRF52 DK. I am very new in the evaluation and testing of BLE Chips...
Hi
I am trying to implement long writes on the gatt server side. My implementation is stack handled, so I am going for the " GATTS Queued Writes: Stack handled, one or...
Hello,
As a power source I am using a battery with an open circuit voltage of 3.67V.
The specification states that the recommended absolute maximum supply voltage is 3...
Hello,
I'm trying to make a communication with a nrf51822 and an trf7970a nfc reader. The communication is based on SPI, I read that there are problems with softdevices...
Hi there..
I need central device simulator to test my UART App.
Is their any facility available for Nordik UART peripheral simulator like ANTware in ANT+ wireless protocol...
