Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hello:
I am writing a BLE profile involving several characteristics. One of the characteristics is an operation code (read/write) tunnel.
Each time a BLE central device...
This situation occured just in Android phone,iphone have not meet this situation.
A detailed description as follows:
After DFU used Android phone,connect again,notify...
Hi, I want to send data from arduino to nrf51dk which will then use uart service to send the data over bluetooth.
I want to use SPI communication between the two microcontrollers...
I have read these the following posts:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
But, most of the answers are quite old. I am wondering if the solution...
I've seen several similar questions -- none of which were concerned with the bootloader project.
I believe the linker is looking for sections called .noinit and .bootloaderSettings...
This is slightly off topic (I also posted this in the mbed forums), but I hope maybe someone here would also know.
My goal is to use the newly secure boot loader that was...
I have Inited the pstorage
err_code = pstorage_init();
APP_ERROR_CHECK(err_code);
Here PSTORAGE_NUM_OF_PAGES=2(1page for bonding ,1page for my application use )...
hi,
I am working with nrf51822 development board using Softdevice(s130) and sdk 11.0.0.I implemented whitelisting in ble_app_uart code but it's not working correctly.Once...
I'm using the example bootloader from SDK 12.1.0 with gcc, nRF51822, S130. I flash the SD, bootloader and my application in that order like this:
flash: all
$(NRFPROJ...
Hi,
IAR ARM 7.60.2
Nrf52
Softdevice 132 v3.0
SDK 11
I am trying to use SPI with easy DMA. I have implemented the PAN 58 workaround for sending 1 byte but it fails...
I got started with bluetooth learning. But it's too hard to understand ble protocol. Do I have to learn BLE protocol even If my purpose is only ble communication with simple...
Hi,
Could someone help me about the following questions?
Q1: What are the connection parameters set by the Android app nRF Connect? Can I change them?
Q2: How can...
