I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi all,
I am trying to update the bootloader, softdevice and application all in a ZIP package through DFU, and at 99% after upload it stop and throws the error:
...
Dear Engineer:
I am a developer of the nRF51822;Some costomers want to send a large number data over the bluetooth,So they require a high quality in speed;I want to know...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
Hi. I want to attach a sensor with SPI slave interface to the nRF52 Preview DK (PCA10036) using the SPIM1 with EasyDMA. Below I have two related questions:
In PAN...
It seems that in SDK9 the APP_BUTTON_INIT() macro has disappeared, and with it the extra argument that determines whether the scheduler is used or not.
However, the documentation...
Hi,
I want to develop one FOB key which will be in TX mode only to transmit a key continuously or at specified interval at ultra low power mode and powered by CR2032 coin...
I'm having really terrible RF performance with a PCB I've designed using a nRF51822 QFAC, Johanson 2450BM14E0003 balun, and a PCB IFA (from TI DN0007: www.ti.com/.../swru120b...
I would like to create a large “virtual” read only characteristic that does not fully exist in memory. I understand that large characteristics are transferred in chunks of...
I am trying to enable a critical section in handler. I need to update a sensitive global variable when a button event occurs, and the fact to enable/disable the interrupt...
I have nrf51822 and I use latest SD130. I scan nearby ble devices. In my case they are iPhones. When one device is in rage then I connect to it and start scan again and keep...
Hello to everyone!
So, now I try to enable a DFU for nrf51822 (S110 7.3.0)and have some problems with it.
I can't find a good example project including DFU, all that I...
I've created a simple test to demonstrate pstorage store/load for 64 pages of 1024 bytes each. To allow 64 flash pages I set PSTORAGE_MAX_APPLICATIONS to 64. Each page stores...
I've been following the custom service nAN-36 instructions and have it mostly working on my PCA10028 board, but I have two problems that I just can't figure out. I'm pretty...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
