Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Is there any way to get some "modern" content assist features in µVision that work with the Nordic SDK? If they're there, I haven't had any luck finding them. After having...
I'm trying to decide whether to use FreeRTOS or simply build on the Scheduler. What are the risks and benefits of using freeRTOS or another RTOS on a wearable sensor device...
Is it possible to connected two separated antennas (single ended), one for RX and another for TX communications to the receiver and transmitter of the NRF51 or NRF52?
Thanks...
In other words, is it safe to assume that in various BLE events, conn_handle is either invalid (0xFFFF) or between 0 and (CENTRAL_LINK_COUNT + PERIPHERAL_LINK_COUNT - 1) ...
I'm digging my way through the examples, SDK code, etc, and I'm curious if it's possible to light an LED if the nRF52832 is reaching an error status. This is mainly so I can...
Hello,
I am seeing a strange problem with the nRF52 RADIO peripheral: sometimes a packet will be received that is corrupted, but the CRCSTATUS register indicates the CRC...
My company is developing an embedded product based on NRF52 and until now we are
using Master Control Panel (MCP) to test BLE communication. MCP is a great tool
but we need...
Hi,
when trying to connect to a 51822 target, using for example OOCD
I keep getting
....
Open On-Chip Debugger 0.10.0-rc1-dev-00001-gc404ff5-dirty (2016-12-29-19:45...
I use PPK wit ha stardard setup with all switches set to DK. Everything works fine, excepted that I have a little offset and the IDLE state is negative... which make the AVG...
I have designed a few PCBs using the NRF52 chip with a standard QFN48 pattern. On the first design, we had 8 PCB's made of which, only 2 worked correctly. The others all exhibited...
Hello,
I received BLE_ERROR_GATTS_SYS_ATTR_MISSING event during connection procedure. Tried to look inside and found
/**@brief Event structure for @ref BLE_GATTS_EVT_SYS_ATTR_MISSING...
In code:
case PM_EVT_BONDED_PEER_CONNECTED:
NRF_LOG_DEBUG("Connected to previously bonded device\r\n");
err_code = pm_peer_rank_highest(p_evt->peer_id);
i get...
Hello there,
We're getting an assert in the above code in Soft Device s110 sdk 8.0.3. Can you give us some info as to what that is and how we can address it? To give you...
