I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hello everybody,
I have a NRF51-DK board and I want to acquire some NRF24LE1 chips. I haven't used the NRF51-DK a lot but I have seen somewhere that it is possible to flash...
Hello Nordic,
I have a question: how do I send a message from a slave to a master? I want to do the same as sd_ant_acknowledge_message_tx, starting the communication from...
Hi,
I am using nRF51422 DK with S130 SoftDevice. I modified ble_app_uart example and I saw my board show in bluetooth setting of my android phone but dit not see anything...
Dear Nordic,
We have a very strange issue regarding NRF52 consumption.
We found that the NRF52 will continously consume 7mA even when we enter in sd_app_evt_wait().
After...
Sorry about a so broad question. But this is what I have experienced but don't know where to look.
I have done a few project using BLE with RTX. Just typical stuff similar...
For Setting the easyDMA on I2C, Do I need just to set the TWI0_USE_EASY_DMA to 1 ?
Also do I need to set an arrayList? which?
or can I just use the same settings that...
Hello,
My team wants to develop a custom iphone application and we want to use it to connect with NRF52 which is transmitting data using the Nordic UART service. We were...
Hii,
I am trying to update new firmware in nRF51-DK.
But unfortunately, wrong image file is uploaded.
Now i am trying to once again same process then getting no space...
I am testing the SDK (v12) Power Profile Example with the DK51 and the nRF51 dongle. My purpose is test if I can lower the power consumption as mush as possible. The default...
I am developing software for a custom hardware based on NRF52. Previously I was tasked on updating the old NRF51 based software (used on older version of the device) for NRF52...
hi,
i am using FDS to store some Data in nRF51 Development kit using temporary application. it is around 2kb. after that i am flashing main Application. is my application...
I am working on a battery-powered application. Since power saving is a must, this design using high-side power node controllers (part number MIC94042) to power-on or power...
Hi
I am looking for pin numbers for the nRF51822 microcontroller.
example like what are the pin numbers for VDD to measure battery voltage..??
I mean in which header...
Hello!
I'm learning how to use properly the saadc for knowing muy battery state of discharge. First of all I'm testing the saadc example which is included in the SDK, changing...
