Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
If BLE device is sleeping,is link layer connection terminated or the link layer connection is still valid..?
if it is valid..how the master will know about the sleeping periods...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
Hi Nordics!
I am using app_pwm.c file in SDK 8.1, and when I use it with softdevice(advertising or data transfer event), sometimes pwm signal is reversed.
I guess, reversed...
Hi Guys,
I am using a the 350Mhz Analog Oscilloscope HM303-6 www.hameg.com/hm303-6.0.html to measure the voltage utilised by the board when it is transmitting data.
...
Hi,
Once I enter into BLE mode I am not able to read any gpios(nrf_gpio_pin_read) also I am not able to set any gpios (nrf_gpio_pin_set).
Below is my example
uint8_t...
I'm trying to establish a bond in my project and then perform service discovery, however the discovery is returning the BUSY error.
I tried to wait for the events according...
In SDK 8.0 the bare word asm was re-introduced in nrf_delay.h , causing failures in compilations that use strict C/C++ standard conformance flags. This was noted in earlier...
Hello Developers
I have to solve a problem for which I could not find much information about online, so I am hoping you guys can help me.
I am developing a WIN32 application...
Hello, For some reason the Ble App Uart is not working on my PC anymore. I have gone over Nordic tutorial again however, the LED doesnt blink and I cant detec the device on...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
