Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
There are many links across the Internet to app note nAN-29 ( nRF51 Development with GCC and Eclipse ). In fact, I remember seeing a link to it on the Nordic website just...
Hi,
I am trying to test a UART bootloader with the hci_dfu_send_hex.py from SDK6.1.0
Unfortunately the script seems to crash, below is the output on the windows command...
Let's say I Have an nrf51822 on a small button cell battery having a sensor that is triggered on certain conditions.
What is the most efficient and power saving way to...
Hello. I'm using 24 MHz crystal to feed my MCU and not able to change it to 16 MHz to share with nrf24. Now I'm driving nrf24 XC1 with PWM signal 16 MHz and it works but not...
Hi,
We have NRF51822 chips programmed for specific application and it is working fine as BLE services etc.
In some scenarios, to debug we want to stream data from our...
device_manager_peripheral.c provided via Software Packs in Keil doesn't compile against S110 8.0.0 (or 8.1.0). Its version shows up as 1.1.1. Same thing happens with bsp.h...
By combining some examples, I'm starting to understand how the UART examples works.
Using Keil 8.0.0, and the PCA10003 Board, I'm trying to send a burst of messages over...
I can see and bond nrf51 with android, but with iPhone nothing.
What can i implement for see nrf51 with iPhone?
Can i pair Iphone and nrf51?
Sorry for the very bad english...
The new generation of nRF51822's have a few neat new features, particularly the automatic power management piece, that I would like to potentially leverage in our project...
Hello,
I'm seeing some 67.2kHz reference spurs on the RF signal when I'm turning on the constant carrier mode using the DTM interface on the nRF51822. Layout and circuit...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
