NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
SDK13, S132, nRF52832.
I use whitelist and bond peripherails. But after bonded 20 pcs of peripherials, I can work with only first 8 bonded.
Which parameters should change...
I’m trying to create a nRF8001 device without the need for any keys, because the device will be inaccessible in mounted condition. Additionally the connection must be secured...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
Hello Sir,
we have designed custom PCB using nRF52832, I am little confused for is it OK. I have attached top and bottom layer layout of my PCB please sir review it and...
Hi guys,
I'm struggling over some basic concepts related to the Mesh SDK, specifically with the Bearer layer and why the Mesh SDK uses the Timeslot API. I'll try to explain...
Hi all,
I'm trying to writing a device information service client on top of ble_app_multilink_central example on nRF52830 using SDK14.1.0 and softdevice 5.0 and have a...
Hello World,
I checked the Developers Zone, but I have not found the direct example of my problem.
I use the RuuviTag board with NRF52832_XXAA.
I use it as a development...
Hello,
I have question about signal names in datasheet nRF52840.
On the pins B19 and T2 on page 14 both pins have the same initial signal names (P0.11).
Please send me...
Hello,
I would like to add the ST7735 driver from the nRF5_SDK to the Mesh SDK along with the necessary components (SPI,..). I copied the entire components directory to...
How is the health model supposed to work?
I'm currently doing some tests with the light switch example and I don't really understand the different roles of the nodes in the...
Hello,
I have some trouble to write/read data in flash region,
I am using FICR region to save data,
if trying the command : nrfjprog --memrd 0x10000010 --n 0x10
I...
Hello All
I am using an SOC which has nrf51822. I am trying the blinky example with the softdevice. When I debug the code, the code first enters the SystemInit function...
