I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Using S130 to request notifications of radio activity as:
fails with NRF_ERROR_INVALID_PARAM.
Is there a reason this combination is disallowed? The use case for it is...
I would like to add the UART part to my application. But I will get these errors:
..........\components\libraries\uart\app_uart_fifo.c(109): error: #20: identifier "UART0_CONFIG_PSEL_TXD...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
