Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
I successfully ran the proximity_demo supplied by Nordic. I used my laptop's usb port to power up the device and it worked fine.
Then I unplugged my laptop and tried to...
Hi dear All!
We going to prepare final PCB Layout for nRF52840 MCU.
Previously, we used nRF52840 -AA , then -BB (pinouts changed!),
The question is about release / next...
Using NRF2401+, I have two units running side by side on the bench.
With Auto-Ack turned OFF I can successfully read the RPD register (bit 0) and get the expected readings...
I have a small problem with Bootloader + application in our custom board.
If I do the DFU update,application starts at first time but if i do a power reset application doesn...
Hello,
Some time ago I bought an nRF51822 evaluation kit to start developing with this chip. Now I have a project that needs a small pcb like the beakon you show here www...
Hello,
I am using the following code to set time in my code, but when trying to set 2100 year or 2040 more year with nrf_cal_set_time function,
it is failed, it shows...
Is it possible to send an SMBus quick write and quick read using the TWI hardware?
The sequence is:
<START><ADDRESS><R/W><ACK><STOP>
I can send the address, but...
Hello,
if I send a byte over uart to an device (e.g. gps -logger), the same byte will printed to the terminal (e.g. Putty or Termite).
If I get a byte from the micro-controller...
I am confused from reading the nRF52832 Product Specification on how to clear the GPIOTE port event (EVENTS_PORT) register?
On Section 21.2 (Port event) on page 158, it...
I am experiencing a difference in current between the example program during advertising between a IAR compilation and a GNU compilation.
The differences appear to be significant...
Hi,
Can the Nordic SoftDevices be consumed by a BareMetal ARM GCC compiled application?
Which compiler/linker flags are needed for the application to be able to link...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
